The United States, Mexico, and Canada reached an agreement to modernize the 25-year-old NAFTA into a 21st century, high-standard agreement. The new United States-Mexico-Canada Agreement (USMCA) supports mutually beneficial trade leading to freer markets, fairer trade, and robust economic growth in North America.
Free-Standing Overhanging Objects. (Shows a horizontal panel mounted on two posts). When the horizontal distance between detectable posts or detectable objects is greater than 12 inches (302 mm), the maximum height to the bottom of the free-standing object is 27 inches (685 mm).
nfpa 11 pdf free 26
Slopes of curb ramps shall comply with 4.8.2. The slope shall be measured as shown in Fig. 11. Transitions from ramps to walks, gutters, or streets shall be flush and free of abrupt changes. Maximum slopes of adjoining gutters, road surface immediately adjacent to the curb ramp, or accessible route shall not exceed 1:20.
Spout Height and Knee Clearance. The front edge of the fountain must extend 17 to 19 inches (430 - 485 mm) from the wall. The 27 inches (685 mm) high minimum clear knee space must be free of equipment or obstructions for a minimum of 8 inches (205 mm) extending from the front edge of the fountain back toward the wall. In addition, a minimum 9 inches (230 mm) high toe clearance space must be provided extending back toward the wall to a distance no more than 6 inches (150 mm) from the back wall. The toe clearance space must be free of equipment or obstructions.
Lavatory Clearances. The minimum knee clearance must be free of equipment or obstructions for a minimum of 8 inches (205 mm) extending from the front edge of the lavatory back toward the wall. This knee clearance must be 29 inches (735 mm) high at the front of the lavatory and no less than 27 inches (685 mm) high at a point 8 inches (205 mm) back. In addition, a minimum 9 inches (230 mm) high toe clearance must be provided extending back toward the wall to a distance no more than 6 inches (150 mm) from the back wall. The toe clearance space must be free of equipment or obstructions.
(7) Kitchens, Kitchenettes, or Wet Bars. When provided as accessory to a sleeping room or suite, kitchens, kitchenettes, wet bars, or similar amenities shall be accessible. Clear floor space for a front or parallel approach to cabinets, counters, sinks, and appliances shall be provided to comply with 4.2.4. Countertops and sinks shall be mounted at a maximum height of 34 in (865 mm) above the floor. At least fifty percent of shelf space in cabinets or refrigerator/freezers shall be within the reach ranges of 4.2.5 or 4.2.6 and space shall be designed to allow for the operation of cabinet and/or appliance doors so that all cabinets and appliances are accessible and usable. Controls and operating mechanisms shall comply with 4.27.
EPA issued decisions on refrigerants and solvent cleaning sectors found acceptable subject to use conditions. The refrigeration sector deals with end-uses both retrofit and new equipment. HCFC Blend Beta was found as acceptable subject to use conditions for motor vehicle air conditioning. Blend B was found acceptable subject to use conditions for; centrifugal chillers, chillers, industrial process refrigeration, skating rinks, storage warehouses, refrigerated transport, food refrigeration, ice machines, freezers, dehumidifiers, and air conditioners. HCFC-225 ca/cb is decided as a substitute for CFC-113 and MCF acceptable to use conditions in precision and metals cleaning. Various other substitutes were found unacceptable for refrigerants and air conditioning as well as in the solvents cleaning sector.
This notice lists GHG-X5, MT-31, HCFC-22, HCFC-142b, and GHG-X5 as substitutes for foam blowing, refrigeration, and air conditioning. The foam blowing end uses are HCFCs, polyurethane integral skin with an acceptable substitute of sub-saturated light hydrocarbons C3-C6. CFC-12 centrifugal and reciprocating chillers, industrial process refrigeration, cold storage warehouses, refrigerated transport, retail food refrigeration, vending machines, water coolers, commercial ice machines, household refrigerators, household freezers, and residential dehumidifiers (retrofitted and new). Also, CFC-12 motor vehicle air conditioning, automotive and non-automotive (retrofitted and new).
DescriptionEPA issued decisions on refrigerants and solvent cleaning sectors found acceptable subject to use conditions. The refrigeration sector deals with end-uses both retrofit and new equipment. HCFC Blend Beta was found as acceptable subject to use conditions for motor vehicle air conditioning. Blend B was found acceptable subject to use conditions for; centrifugal chillers, chillers, industrial process refrigeration, skating rinks, storage warehouses, refrigerated transport, food refrigeration, ice machines, freezers, dehumidifiers, and air conditioners. HCFC-225 ca/cb is decided as a substitute for CFC-113 and MCF acceptable to use conditions in precision and metals cleaning. Various other substitutes were found unacceptable for refrigerants and air conditioning as well as in the solvents cleaning sector.
Description:This notice lists GHG-X5, MT-31, HCFC-22, HCFC-142b, and GHG-X5 as substitutes for foam blowing, refrigeration, and air conditioning. The foam blowing end uses are HCFCs, polyurethane integral skin with an acceptable substitute of sub-saturated light hydrocarbons C3-C6. CFC-12 centrifugal and reciprocating chillers, industrial process refrigeration, cold storage warehouses, refrigerated transport, retail food refrigeration, vending machines, water coolers, commercial ice machines, household refrigerators, household freezers, and residential dehumidifiers (retrofitted and new). Also, CFC-12 motor vehicle air conditioning, automotive and non-automotive (retrofitted and new). 2ff7e9595c
Comments